Author: Fedotov, A.V.
Paper Title Page
TUPG35 LEReC Instrumentation Design & Construction 417
  • T.A. Miller, M. Blaskiewicz, K.A. Drees, A.V. Fedotov, W. Fischer, J.M. Fite, D.M. Gassner, R.L. Hulsart, D. Kayran, J. Kewisch, C. Liu, K. Mernick, R.J. Michnoff, M.G. Minty, C. Montag, P. Oddo, M.C. Paniccia, I. Pinayev, S. Seletskiy, K.S. Smith, Z. Sorrell, P. Thieberger, J.E. Tuozzolo, D. Weiss, A. Zaltsman
    BNL, Upton, Long Island, New York, USA
  Funding: Work supported by Brookhaven Science Associates, LLC under Contract No. DE-AC02-98CH10886 with the U.S. Department of Energy
RHIC will be run at low ion beam center-of-mass energies of 7.7 - 20 GeV/nucleon, much lower than the typical operations at 100 GeV/nucleon. The primary motivation is to explore the existence and location of the critical point on the QCD phase diagram. An electron accelerator is being constructed to provide Low Energy RHIC electron Cooling (LEReC) to cool both the blue & yellow RHIC ion beams by co-propagating a 10 - 50 mA electron beam of 1.6 - 2.6 MeV. This cooling facility will include a 400 keV DC gun, SRF booster cavity and a beam transport with multiple phase adjusting RF cavities to bring the beam to one ring to allow electron-ion co-propagation for ~21 m, then through a 180° U-turn electron transport so that the same electron beam can similarly cool the other counter-rotating ion beam, and finally to a beam dump. The injector commissioning is planned to start in early 2017 and full LEReC commissioning planned to start in early 2018. The instrumentation systems that will be described include current transformers, BPMs, profile monitors, multi-slit and single slit scanning emittance stations, time-of-flight and magnetic energy measurements, and beam halo & loss monitors.
poster icon Poster TUPG35 [14.455 MB]  
DOI • reference for this paper ※ DOI:10.18429/JACoW-IBIC2016-TUPG35  
Export • reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)  
WEPG19 Conceptual Design of LEReC Fast Machine Protection System 665
  • S. Seletskiy, Z. Altinbas, M.R. Costanzo, A.V. Fedotov, D.M. Gassner, L.R. Hammons, J. Hock, P. Inacker, J.P. Jamilkowski, D. Kayran, K. Mernick, T.A. Miller, M.G. Minty, M.C. Paniccia, I. Pinayev, K.S. Smith, P. Thieberger, J.E. Tuozzolo, W. Xu, Z. Zhao
    BNL, Upton, Long Island, New York, USA
  The low energy RHIC Electron Cooling (LEReC) accelerator will be running with electron beams of up to 110 kW power with CW operation at 704MHz. Although electron energies are relatively low (< 2.6MeV), at several locations along the LEReC beamline, where the electron beam has small (about 250 um RMS radius) design size, it can potentially hit the vacuum chamber at a normal incident angle. The accelerator must be protected against such a catastrophic scenario by a dedicated machine protection system (MPS). Such an MPS shall be capable of interrupting the beam within a few tens of microseconds. In this paper we describe the current conceptual design of the LEReC MPS.  
DOI • reference for this paper ※ DOI:10.18429/JACoW-IBIC2016-WEPG19  
Export • reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)